Euserv一键起飞脚本

ChenYFan

1. wget https://euserv.cyfan.top/euserv.sh?PKey=aCKO5M5QoIAae8HxYpcClOgtFcqumYw9OnuWmOI8IGg= -O one.sh
   
2. chmod +x one.sh
   
3. ./one.sh

复制代码

脚本作用：动态生成WGCF配置文件并一键完成Warp链接

euserv.cyfan.top为纯ipv6网站，eu机能直接连接。

aCKO5M5QoIAae8HxYpcClOgtFcqumYw9OnuWmOI8IGg=为公号PrivateKey

公号的deviceid为9c0039d3-d62e-4845-86d5-f14b98c293af，如果你愿意，可以为他刷一点Plus流量！




PKey指的是Warp配置文件中的PrivateKey，如果你有Plus，请自行替换【特殊字符请自行UrlEncode


或者一把梭：

1. bash <(curl -fsSL https://euserv.cyfan.top/euserv.sh?PKey=aCKO5M5QoIAae8HxYpcClOgtFcqumYw9OnuWmOI8IGg=)

复制代码

mjj试试能不能用？

optimism

感谢分享 技术贴必顶

星如雨落

666666p

ChenYFan

h20 发表于 2021-7-12 20:18
卡的动不了

脚本地址为纯ipv6，请尝试在eu鸡上运行

EasyFame

开了这个之后能干什么啊？我小白，给个基础教程链接

EasyFame

1. ● [email protected] - WireGuard via wg-quick(8) for wgcf
   
2.      Loaded: loaded (/lib/systemd/system/[email protected]; enabled; vendor preset: enabled)
   
3.      Active: failed (Result: exit-code) since Mon 2021-07-12 14:31:17 CEST; 42s ago
   
4.        Docs: man:wg-quick(8)
   
5.              man:wg(8)
   
6.              https://www.wireguard.com/
   
7.              https://www.wireguard.com/quickstart/
   
8.              https://git.zx2c4.com/wireguard-tools/about/src/man/wg-quick.8
   
9.              https://git.zx2c4.com/wireguard-tools/about/src/man/wg.8
   
10.    Main PID: 9513 (code=exited, status=1/FAILURE)
    
11. 
    
12. Jul 12 14:31:17 srv22390 systemd[1]: Starting WireGuard via wg-quick(8) for wgcf...
    
13. Jul 12 14:31:17 srv22390 wg-quick[9513]: [#] ip link add wgcf type wireguard
    
14. Jul 12 14:31:17 srv22390 wg-quick[9520]: Error: Unknown device type.
    
15. Jul 12 14:31:17 srv22390 wg-quick[9522]: Unable to access interface: Protocol not supported
    
16. Jul 12 14:31:17 srv22390 wg-quick[9513]: [#] ip link delete dev wgcf
    
17. Jul 12 14:31:17 srv22390 wg-quick[9523]: Cannot find device "wgcf"
    
18. Jul 12 14:31:17 srv22390 systemd[1]: [email protected]: Main process exited, code=exited, status=1/FAILURE
    
19. Jul 12 14:31:17 srv22390 systemd[1]: [email protected]: Failed with result 'exit-code'.
    
20. Jul 12 14:31:17 srv22390 systemd[1]: Failed to start WireGuard via wg-quick(8) for wgcf.
    

复制代码

ubuntu 18.04 安装失败 似乎是内核不支持wireguard

笑花落半世琉璃

算了吧，就德基那德行，临时用用用还行

EasyFame

EasyFame 发表于 2021-7-12 21:24
ubuntu 18.04 安装失败 似乎是内核不支持wireguard

找到原因了，脚本里有一句 curl -fsSL git.io/wireguard-go.sh | sudo bash 纯ipv6环境下不下来

本人马保国

学习下